このマニュアルは英語または説明に記載されている言語で作成されることにご注意ください
Original Factory Illustrated Operating manual For Linde Forklift Truck 351-02 series with Diesel Engine Covered models: H20-02 H25-02 H30-02 Format: PDF, 80 Pages Language: English Table of contents: Description Approved applications Technical note Truck takeover Type plates Technical data Technical description Engine Hydraulic system Operation Brakes Steering Electrical system General view Controls and indicators Composite instrument Beginning operation Safty rules Important safety information Handling fuels and lubricants Accident prevention check Particle filter inspection Running-in instructions Checks and services before initial operation Daily checks Daily pre-operational checks and services Opening the engine cover Checking the engine oil level Checking the fuel level Filling fuel Hydraulic system: Checking the oil level Checking the fluid level in coolant reservoir Adjusting the driver's seat Checking the typre pressure Starting the engine Cold start Stopping the engine Malfunctions during operation Operation Travel Forward travel Reverse travel Changing the travel direction Single-pedal model Steering system, Braking system Steering Service brake Parking brake Applying the parking brake Releasing the parking brake Lifting device and attachments Tilting the mast forward Tilting the mast back Lifting the fork carriage Lowering the fork carriage Operating the attachments Operating the sideshift Operating the clamp Single-lever operation of lifting device and attachments Turning on the windscreen wipers Switching on the lights Switching on the hazard warning light Turning on the ventilation Front working lights Rear working lights Heater Heater controls Fan motor fuse Operating the horn Fuses Before lifting a load Adjusting the fork spread Loading Travel with a load Unloading Before leaving the lift truck unattended Hoisting the truck with a crane Hoisting the truck with a crane using the lifting eyes Jack locations when changing wheels Trailer coupling Mast removal Towing instructions Towing Towing procedure Releasing the wheel drive brake pressure Opening the hydraulic by-pass valve After towing Re-establishing braking power Taking the truck out of operation Measures before taking the truck out of operation Putting the truck back into operation Maintenance General information Work on the mast and on the front part of the truck Securing the mast against tilting back Standard mast Securing the raised standard mast Duplex mast Securing the raised duplex mast Triplex mast Securing the raised triplex mast Checks and services after the first 50 service hours Inspection and maintenance chart Inspection and maintenance as required Cleaning the lift truck Cleaning and spraying the mast chain Cleaning the air filter Cleaning with compressed air Wet cleaning Replacing the safety element Checking the dust discharge valve Cleaning the prefilter Checking the mounting of the steering cylinder and king pin at the steering axle Regenerating the particle filter Cleaning and checking radiator and hydraulic oil cooler for leaks Drain the fuel system water preseparator Tightening the wheel nuts Check the tyres for damage and foreign objects 250-hour inspection and maintenance Clean and grease the steering axle Grease the mast and tilt cylinder pivots Check electric cables, cable connectors and connections for condition and tightness Drain the fuel system water preseparator Sideshift: clean and grease, check the mounting Battery: Check condition, electrolyte level and specific gravity 500-hour inspection and maintenance Check the mast and mast chains for condition and security Adjust the mast chain length and lubricate with chain spray Change the engine oil (every 12 months minimum Drain the engine oil Renew the engine oil filter Top up engine oil Check coolant strength Check the mounting of the compact axle at the engine Check the engine mounting, counterweight, overhead guard, steering axle and wheel drives for tightness Check and oil the pedals, travel control and engine control linkages Check the tension and condition of the alternator and fan V-belt Tighten the alternator and fan V-belt Renew the fuel filter (every 12 months minimum) Clean the radiator and hydraulic oil cooler Checking the particle filter system Check and oil other pivots and joints Check the fork stops and fork quick-releases Check the pre-tension of double hoses if attachments are fitted 1000-hour inspection and maintenance Renew the air filter element, check the vacuum switch Check the engine mounting for condition and tightness Check the air intake and exhaust pipes for leaks Check the hydraulic system, compact axle, pumps, valves and lines for leaks Hydraulic system: Renew the pressure, suction and breather filters Renew the pressure filter Renew the suction filter Renew the breather filter Check the wheel drive oil level Check the particle filter system Check the parking brake 2000-hour inspection and maintenance Renew the alternator and fan V-belt Tighten the V-belt Check the injection nozzles Check, adjust valve clearance Check the particle filter system 3000-hour inspection and maintenance Renew the hydraulic oil Check the mounting of the compact axle on engine Inspection and maintenance data Fuel and recommendations Engine oils Oil grades Oil viscosity Diesel fuel Hydraulic oil Lubricating grease Coolant Battery grease Chain spray Engine Troubleshooting guide (diesel engine) Troubleshooting guide (hydraulic system) Wiring diagram Hydraulic circuit schematic Index